Below is a short overview of STP and how to navigate it in the CISCO IOS enjoy.
[youtube=http://www.youtube.com/watch?v=zapAZRP7mEk&w=560&h=315]
Below is a short overview of STP and how to navigate it in the CISCO IOS enjoy.
[youtube=http://www.youtube.com/watch?v=zapAZRP7mEk&w=560&h=315]
Moving forwards the next bunch of topics on the list look like so:
So lets first get a little background on OSPF before moving any further.
OSPF or Open Shortest Path First is, as the name suggest, an open standard link state routing protocol. The AD of OSPF is 110 and OSPF uses a metric of the outgoing interface Cost to determine the best route. It’s a fast converging and flexible routing protocol which also enables us to separate the topology into areas.
The Topology data for the OSPF network is contained within Link State Advertisements and all routers in the same area share the exact same topology information.
I won’t delve any further into OSPF at this point, i just simply want to introduce the upcoming topics and as you can see there are a few things to get through. So in the upcoming days i will describe the purpose of the LSA’s the RID , configuration and some helpful troubleshooting commands.
Don’t stress too hard this stuff is pretty easy.
On our journey through the Cisco ICND2 objectives, we are expected to know a thing or two about “Metrics”
So what is a metric you ask ?
Well a routing metric is used by all routing protocols to decide on the best path to any given network. Not to be confused with Administrative Distance (AD). Which tell the router which path to believe when a router learns a route from more then one routing protocol.
Below is an example of what a metric is, with the use of RIPv2. As you can see R1 has two paths to reach R2. One is out FA0/1 directly to R2 (Which in the real world would be a connected route with a lower AD then RIP) and out FA0/2 through R3.
The metric with RIP is calculated using hop count, so the path with the least hops is the best path. The path highlighted in red would be used in this example.
The next routing protocol feature to talk about is Split Horizon.
A feature of Distance Vector that prevents routing loops from forming. Split horizon rules stop a router from sending routing updates back out the interface from which it learnt them from.
Split horizon is used with RIPv2 and EIGRP and yup you guessed it they are Distance Vector routing protocols.
The example below gives you some understanding of what Split Horizon is actually doing. The RIP update going out R1’s FA0/1 interface only includes the subnet 192.168.0.0/24 (Route highlighted in red). As you can see from the routing table below, R1 learnt this network from an update off FA0/3, so Split Horizon Rules allow this network to be sent in an update out FA0/1.
The routes highlighted in black, are learnt from FA0/1 so Split horizon rules will not allow these routes to be sent in an update, over FA0/1
[youtube http://www.youtube.com/watch?v=rtiDfh-CILs&w=560&h=315]

Serial Link
Setting the Clock Rate (CLOCK RATE INTERFACE COMMAND)
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int serial 1/0
Router(config-if)#clock rate ? (Can be either clockrate or clock rate depending on model)
With the exception of the following standard values not subject to rounding,
1200 2400 4800 9600 14400 19200 28800 38400
56000 64000 128000 2015232
accepted clockrates will be bestfitted (rounded) to the nearest value
supportable by the hardware.
<246-8064000> DCE clock rate (bits per second)
Router(config-if)#clock rate 56000
Router(config-if)#^Z
Remember the DCE Provides the clock rate to the DTE and without this, your line protocol will remain down
Well i decided to start creating my own labs, and since i dont have access to any physical routers/switches i decided to use GNS3 which is a great simulator of CISCO. Now what i am putting forward is my first attempt at creating a network and what i got was no ICMP echo replies from each router. Now i have rectified this fault and I’m excusing my mistake because it was 3:10 in the morning (dont ask i cant sleep) but can you spot why this network has no connectivity ?
I will post the answer within the week good luck , This shouldn’t take you too long to figure out 😀 Happy trouble shooting.